Welcome, Guest. Please login or register.

Author Topic: Kegging, bottle heavy franboise carboy  (Read 5366 times)

Offline Alain2

  • NBCBA
  • Junior Poster
  • **
  • Posts: 153
  • 2 stroke motorcycles and mountain bikes
  • Liked:
  • Likes Given: 63
Kegging, bottle heavy franboise carboy
« on: November 05, 2017, 09:41:29 AM »
How the hell do I take out the beer of the keg without making a mess and oxidized everything?

Offline Alain2

  • NBCBA
  • Junior Poster
  • **
  • Posts: 153
  • 2 stroke motorcycles and mountain bikes
  • Liked:
  • Likes Given: 63
Re: Kegging, bottle heavy franboise carboy
« Reply #1 on: November 05, 2017, 09:42:45 AM »
Forgot to mention there are franboise at the bottom too, you can't see it on the pic.

Offline feldmann

  • NBCBA
  • Senior Poster
  • ***
  • Posts: 737
  • Liked:
  • Likes Given: 230
Re: Kegging, bottle heavy franboise carboy
« Reply #2 on: November 05, 2017, 10:35:25 AM »
Noble grape used to sell these clips that will hold the siphon in place, you could probably just as easily use duct tape or something. I'd just position the siphon right above the fruit on the bottom of the carboy and then siphon until the fruit on top gets close to the bottom but before it reaches the siphon.

A tip I learned a little while ago was to puree fruit before adding it into a carboy. It gets the same/better effect and is much less of a mess.

Offline Alain2

  • NBCBA
  • Junior Poster
  • **
  • Posts: 153
  • 2 stroke motorcycles and mountain bikes
  • Liked:
  • Likes Given: 63
Re: Kegging, bottle heavy franboise carboy
« Reply #3 on: November 05, 2017, 12:37:08 PM »
Ok great trick, I'll use duck tape to hold it at the right place. But then I feel I will be leaving a lot of precious beer in the fruits/slurry. I would like to extract as much as I can, I could strain it, but imagine all the oxygenation that would occur. Maybe it's better than dumping it.  :o

Offline feldmann

  • NBCBA
  • Senior Poster
  • ***
  • Posts: 737
  • Liked:
  • Likes Given: 230
Re: Kegging, bottle heavy franboise carboy
« Reply #4 on: November 05, 2017, 02:03:32 PM »
When ever I add fruit or anything like that I just accept a decent amount of beer loss.

Offline robcoombs

  • NBCBA
  • Forum Hero
  • ****
  • Posts: 1453
  • Liked:
  • Likes Given: 703
Re: Kegging, bottle heavy franboise carboy
« Reply #5 on: November 05, 2017, 02:42:24 PM »
When ever I add fruit or anything like that I just accept a decent amount of beer loss.
This exactly. Aside from volume loss using fruit you have to accept the loss from that layer as well. Unfortunately it's the cost of using whole fruit.

Sent from my SM-G935W8 using Tapatalk


Offline Alain2

  • NBCBA
  • Junior Poster
  • **
  • Posts: 153
  • 2 stroke motorcycles and mountain bikes
  • Liked:
  • Likes Given: 63
Re: Kegging, bottle heavy franboise carboy
« Reply #6 on: November 05, 2017, 04:59:15 PM »
Ok thanks guys

Offline shazapple

  • NBCBA
  • Junior Poster
  • **
  • Posts: 321
  • Liked:
  • Likes Given: 417
Re: Kegging, bottle heavy franboise carboy
« Reply #7 on: November 06, 2017, 02:52:10 PM »
That looks delicious!
Lee

Offline dswan75

  • NBCBA
  • Newbie
  • *
  • Posts: 18
    • Facebook Page
  • Liked:
  • Likes Given: 25
Re: Kegging, bottle heavy franboise carboy
« Reply #8 on: November 06, 2017, 08:21:02 PM »
is it worth purging a bit of co2 in as your siphoning out? Not pressurizing but just drop a line in there and crack the regulator? 

Offline ECH

  • Junior Poster
  • **
  • Posts: 313
    • Elm City Hobbies
  • Liked:
  • Likes Given: 0
Re: Kegging, bottle heavy franboise carboy
« Reply #9 on: November 09, 2017, 02:26:40 AM »
When I ferment in a carboy, I just use a racking cane to get it out. Once it gets down towards the bottom, tip the carboy over slowly about 20 degrees to get the last of the bottom. Once you do that, there really isn't that much left in the bottom.

Offline robcoombs

  • NBCBA
  • Forum Hero
  • ****
  • Posts: 1453
  • Liked:
  • Likes Given: 703
Re: Kegging, bottle heavy franboise carboy
« Reply #10 on: November 09, 2017, 08:47:08 AM »
is it worth purging a bit of co2 in as your siphoning out? Not pressurizing but just drop a line in there and crack the regulator?

I don't think this would be of much benefit if racking to a bottling bucket. But if kegging there are accessories to buy that allow you to transfer with co2 and avoid oxygen exposure. However this should only ever be done with a PET vessel, never glass.